YouTube Drones Courses List

This tutorial series covers the process of building an AI-controlled drone, from gesture control with OpenCV AI Kit to precision landing and autonomous flight. It also includes a demonstration of a drone following the user, using AI technology. This tutorial is perfect for those interested in learning more about AI-controlled drones. View all

This course provides an in-depth guide on how to build a drone capable of reaching speeds of over 100mph. It covers the installation of motors, cutting wires, building the frame, mounting motors, soldering VTX and Crossfire, battery cable, and camera wire. With this course, users will be able to construct a powerful and fast drone that can be used for a variety of purposes. View all

This course teaches viewers how to build a FPV Quadcopter. Part 2 covers setting up a non-PPM receiver, binding the receiver to the transmitter, setting up the Naze32 board orientation, setting up the Naze32 low battery, setting up the receiver in Baseflight, and motor testing. This course provides viewers with the necessary steps to build a successful FPV Quadcopter. View all

This PROton Long Range 6s Build Part 1 tutorial guides viewers through the process of building a frame, installing motors, rearranging the fc/esc cable, mounting a Helio Spring, wiring a Crossfire RX, installing cam and VTX wires, and installing an XT60 with cap. Finally, viewers are shown how to test and power up the build. View all

This course provides an introduction to building a Lumenier QAV210 quadcopter. It covers the parts needed, such as the Naze32 rev6b and OSDoge, as well as the build schematic and component layout. It also explains how to mount the PDB, prepare and mount the ESCs, solder the Naze32 header pins and ESC signal wires, and install the landing gear. This course provides a comprehensive guide to building a Lumenier QAV210 quadcopter. View all

In this course, a long range 6s quadcopter is built from scratch. Participants learn how to bind the Crossfire Flash, configure receiver modes, install motors and OSD, and program BLHeli32. After completing the build, a final test is conducted and race footage and freestyle footage from a haunted warehouse is shown. This course provides a comprehensive guide to building a long range 6s quadcopter. View all

This course provides a step-by-step guide on how to setup a QAV250 quadcopter. It covers soldering the input connector on the Naze32, setting up switches on the Taranis, binding the d4r-ii to the Taranis, setting up the Naze32 on CleanFlight, calibrating the ESCs, setting the motor directions, and installing the FPV camera and VTX. View all

This course covers the construction of an ultralight quadcopter using the FlightClub PROton. The build list includes parts such as a mount RX and a Smart Audio. During the build, a mistake was made when soldering the Smart Audio to the RX6 instead of the TX6. The schematic on the website was followed to correct the mistake. This course provides a comprehensive guide to building an ultralight quadcopter. View all

This course provides a step-by-step guide on how to build a FPV Quadcopter. It includes a list of parts used, a schematic/diagram, instructions on how to assemble the frame, layout of components and Naze32 orientation, and instructions on how to solder the ESC's and Naze32. It also covers how to install the motors and propellers, as well as how to configure the Naze32. View all

This course provides a comprehensive guide to setting up a Lumenier QAV X. It covers flashing the KISS FC, Taranis setup, telemetry, KISS configuration, calibrating ESCs, motor tests, PIDs, and finishing the build. It also includes instructions for setting up failsafe and a final test flight. This course is ideal for anyone looking to build and fly a Lumenier QAV X. View all

This course provides an introduction to the parts used to build a Lumenier QAV250 quadcopter. It includes a schematic of the build, instructions on how to prepare the ESCs, how to orient the Naze32, how to install the ESC signal wires, how to install the battery cable with wire mesh, how to solder the VBAT, and how to install the motor wire mesh. This course provides all the necessary information to build a Lumenier QAV250 quadcopter. View all

This course provides a step-by-step guide on how to build a Lumenier QAV X. It covers the preparation of the ESCs and motors, removal of the header off the PowerOSD, installation of the camera, vtx cable and battery on the PDB, mounting of the motors, soldering of the ESCs, VBAT cable, KISS FC, XSR cable and ESC signal cables. The course provides a comprehensive guide to building a Lumenier QAV X. View all

Get a comprehensive overview of How to Fly A Drone View all

Explore the essentials of DJI Mini 2 - Beginners Guide View all